Infocus IN82 Manual do Utilizador

IN82 www.infocus.com/supportIN82010-0629-01 *010-0629-01*IN82 User’s GuideUser’s GuideMode d’emploiBenutzeranleitungManual de UsoGuidaall'usoGe

9Displaying an imageConnect the power cord to the Power connector on the back of the projector and to your electrical outlet.NOTE: Always use the powe

10 Adjust the zoom and focus. If the image is not square, adjust the keystone using the Picture menu. See page 20 for details.Adjust the volume on you

11Shutting down the projectorPower SaveThe projector also has a Power Save feature that automatically turns the lamp off after no active sources are d

12Problem Solution Resultno start up screenplug power cord in back of projector press power button on remotecorrect imageonly start up screen appears

13Problem Solution Resultimage not centered on screenmove projector, adjust zoom, adjust heightcorrect imageimage not squareAdjust Keystone in Pictur

14image not sharpAdjust focus or adjust Sharpness in the Picture>Advanced menucorrect imageimage upside downturn off ceiling in Settings>System

15image reversed left to rightturn off rear in Settings>System menucorrect image projected colors don’t match sourceadjust color, tint, color tempe

16Still need assistance?If you need assistance, visit our website at www.infocus.com or call us. This prod-uct is backed by a limited warranty. An ext

17Using the remote controlThe remote uses two (2) AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + a

18Optimizing video imagesYour projector has been factory optimized for excellent performance no matter what the source. However, if you wish to make f

1Declaration of ConformityManufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Louis Armstrongweg 1

19Using the menusTo open the menus, press the Menu button on the remote. (The menus automat-ically close after 60 seconds if no buttons are pressed.)

20Picture menuTo adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Selec

21Presets: This allows you to customize settings and save the settings to be restored later. To restore the factory default settings, choose Factory R

22Advanced menuRemember that not all options in the menus are available for all sources/signals. Iris: adjusts the aperture of the iris from 0 to 100

23Color Temperature: changes the intensity of the colors. Select a value. Native means an uncorrected/unchanged color temperature. Other values change

24Settings menuSources: allows programming of source buttons, enables autosource, and enables the SCART RGB source. When Autosource is selected, the S

25Display Messages: displays status messages (such as “Searching”) in the lower-left corner of the screen.Tra n s l u c e n t O S D (On Screen Displ

26Service: To use these features, highlight them and press Select.Factory Reset: restores all settings to their default.Reset Lamp hours: resets the l

27MaintenanceReplacing the projection lampThe lamp hours timer in the Service Info menu counts the number of hours the lamp has been in use. Twenty ho

284 Loosen the two captive screws on the lamp door and lift the door off.5 Loosen the two captive screws that attach the lamp housing to the projector

2Table of Contents Introduction 3Positioning the projector 5Choosing the aspect ratio 6Connecting a video device 7Video connectors 7Digital connec

29AppendixRemote control discrete codesYou can use these codes to program another remote to learn the projector’s remote functions.To activate discret

30Supported video formatsConnector Signal Type Supported formatsHDMI Digital RGB and YCrCb(HDCP or non-HDCP)1080p/24Hz1080p/50Hz1080p/60Hz1080i/50Hz/6

31RS-232 terminal Product Interface specifications Communication configurationTo control the projector from an LCD control panel, connect an RS-232 ca

32Supported commandsFunction Command RangeDefaultAspect Ratio ARZ 0-50 = Auto 1 = Native 2 = 4:3 3 = 16:9 4 = Letterbox 5 = Natural Wide1Auto Ceiling

33Gamma Table GTB 0-82 = Video3 = Film5 = Bright Room 7 = CRT8 = PC3Green Gain GCG 0-100 128Green Offset GCO 0-100 128HDMI DDC Enable 1 EE1 0-1 1HDMI

34Number of times unit has been turned on for at least 30 min-utesO30 0-65535 0Number of times unit has been turned on for at least 60 min-utesO60 0-6

35System Power Enable SPE 0-1 0System State SYS 0-24 0Test Pattern Enable TPE 0-1 0Test Pattern Select TPS 0-10, 15-21 0Time in Hours Last Bulb1 Laste

36INDEXNumerics12 volt outputs 416x9 18AAdvanced menu 22aspect ratio 6, 20Auto Ceiling 24Auto Image 20Auto Power 24Autosource 24BBlack Level Calibrati

37HHDMI 4, 8, 26HDTV 7, 18, 20High Power 24Horizontal position 22Iimageadjusting 9focus 10size 5zoom 10Image Shift 20Kkeystone adjustment 10, 20Llamp

38SSCART 24screen triggers 4serial connection 8Service 26Service Code 26Service menu 26Settings menu 24sharpness 22Sleep Timer 25Source Enable 24Sourc

3IntroductionYour new InFocus projector is specifically designed for home theater applications. It sets a high standard using the latest DLP™ technolo

4Connector PanelRemove the cable cover, if attached, to access the connector panel. Replace the cover after the projector is installed, if desired.The

5Positioning the projectorTo determine where to position the projector, consider the size and shape of your screen, the location of your power outlets

6Choosing the aspect ratioAspect ratio is the ratio of the image width to image height. HDTV and most DVDs are 16:9, which is the default for this pro

7Connecting a video deviceYou can connect video devices such as HDTV receivers, HD-DVD players, VCRs, camcorders, digital cameras, video game consoles

8HDMI 1.3 connectionHDMI is a standard, uncompressed, all-digital audio/video interface. HDMI pro-vides an interface between sources, such as set-top